How to use the peptide calculator
The peptide calculator converts the three numbers on your bench into the one you need: how far to draw the syringe. It is a reconstitution and mixing calculator for laboratory planning, and it works for any lyophilised vial, whether that is BPC-157 5mg, TB-500 5mg, MOTS-c 10mg or a blend.
- Choose the syringe size (0.3 ml, 0.5 ml or 1 ml). On a U-100 insulin syringe, 1 ml = 100 units.
- Enter the peptide weight in the vial in mg (printed on the label, e.g. 5 mg or 10 mg).
- Enter the volume of bacteriostatic water you will add, in ml.
- Enter the target amount per draw in mcg or mg.
The calculator returns the concentration (mg/ml and mcg per 0.1 ml), the volume to draw in ml and the number of units on the syringe, plus how many draws the vial holds.
The peptide calculation formula
Every peptide calculation uses the same two steps, so you can check any result by hand:
- Concentration (mg/ml) = peptide in the vial (mg) ÷ water added (ml)
- Volume to draw (ml) = target amount (mg) ÷ concentration (mg/ml)
- Syringe units = volume to draw (ml) × 100 on a U-100 syringe
Worked example: a 5 mg vial reconstituted with 2 ml of water gives 2.5 mg/ml (2,500 mcg/ml). A 250 mcg aliquot is 0.25 mg ÷ 2.5 mg/ml = 0.1 ml, which is 10 units on a U-100 syringe. The vial holds 20 aliquots of that size.
Peptide reconstitution chart
This peptide chart shows the concentration you get from common vial sizes and water volumes. The last column is the amount contained in 10 units (0.1 ml) of a U-100 syringe.
| Vial size | Water added | Concentration | Per 10 units (0.1 ml) |
|---|---|---|---|
| 2 mg | 1 ml | 2 mg/ml | 200 mcg |
| 2 mg | 2 ml | 1 mg/ml | 100 mcg |
| 5 mg | 1 ml | 5 mg/ml | 500 mcg |
| 5 mg | 2 ml | 2.5 mg/ml | 250 mcg |
| 5 mg | 2.5 ml | 2 mg/ml | 200 mcg |
| 5 mg | 3 ml | 1.67 mg/ml | 167 mcg |
| 10 mg | 1 ml | 10 mg/ml | 1,000 mcg |
| 10 mg | 2 ml | 5 mg/ml | 500 mcg |
| 10 mg | 3 ml | 3.33 mg/ml | 333 mcg |
| 10 mg | 5 ml | 2 mg/ml | 200 mcg |
| 50 mg | 5 ml | 10 mg/ml | 1,000 mcg |
Peptide blend calculator: vials with more than one compound
For a blend or stack, run the calculator once for each compound using that compound’s weight and the same water volume. Each compound’s concentration is its own weight divided by the shared volume, so one syringe draw contains every compound in the ratio printed on the label.
Units, mg and mcg conversions
- 1 mg = 1,000 mcg
- 1 ml = 100 units on a U-100 insulin syringe, so 1 unit = 0.01 ml
- 0.1 ml = 10 units; 0.25 ml = 25 units; 0.5 ml = 50 units
Peptide calculator FAQs
What does a peptide calculator do?
It turns the vial weight, the volume of water added and a target amount into a concentration and a syringe reading, so reconstituted material can be measured accurately and consistently between experiments.
How much bacteriostatic water should be added to a peptide vial?
There is no single correct volume. Less water gives a stronger solution and smaller draws; more water gives a weaker solution that is easier to measure precisely. Many laboratories choose 1–3 ml for a 5–10 mg vial so that common amounts land on whole units. Read bacteriostatic water vs sterile water before choosing a diluent.
How do I work out BPC-157 reconstitution?
Use the same formula: a BPC-157 5mg vial with 2 ml of water gives 2.5 mg/ml. Our BPC-157 reconstitution guide walks through the full laboratory procedure, and there is a matching PT-141 reconstitution guide.
How long does a reconstituted peptide last?
That depends on the sequence, the diluent and the storage temperature. See reconstituting and storing peptides and do peptides need to be refrigerated for general guidance.
Is this peptide dosage calculator medical advice?
No. The calculator only does arithmetic for laboratory reconstitution. XL Peptides supplies research compounds that are not for human or veterinary use, and nothing on this page is dosing guidance.